TT-P-1757 Primer Coating, Alkyd Base, One Component

The TT-P-1757 specification covers the requirements for two types, classes, and colors of a one-component, alkyd-base, corrosion-inhibiting primer coating.

SKU: 1757. Category: . Tags: , , .

Product Description

The TT-P-1757 specification covers the requirements for two types, classes, and colors of a one-component, alkyd-base, corrosion-inhibiting primer coating.

Classification

Type: The primers coatings consist of the following types:

Type I – Volatile content consists of non-photochemically reactive solvents
Type II – Volatile organic compound (VOC) content less than or equal to 340 grams/liter (gm/l) (2.8 lb./gal)

Class: The primer coatings consist of the following classes:

Class C – Chromate based corrosion-inhibitors
Class N – Non-chromate based corrosion-inhibitors

Color: The primer coating colors consist of the following:

Color Y – Deep yellow
Color T – Green (FED-STD-595, color number 34151)

TT-P-1757A ZINC CHROMATE PRIMER (AMS 3110): A low-moisture sensitivity, corrosion-inhibiting zinc chromate primer. TT-P-1757A Zinc Chromate Primer is a single component, zinc-chromate pigmented, low-moisture sensitivity primer primarily intended for spray application on surface treated aluminum or surface treated with pre-treatment coatings MIL-C-8514C or DOD-P-15328D. This primer may be used with or without top coating. When suitable thinned, this primer may be used for dip or flow-coat application.

TT-P-1757B TY.I, CL.C ZINC CHROMATE PRIMER: A one-component, alkyd base, corrosion-inhibiting zinc chromate primer. TT-P-1757B Ty.I, Cl.C Zinc Chromate Primer is a single component, zinc-chromate pigmented, low-moisture sensitivity primer primarily intended for spray application on surface treated aluminum or surface treated with pre-treatment coatings MIL-C-8514C or DOD-P-15328D. This primer may be used with or without top coating. When suitable thinned, this primer may be used for dip or flow-coat application.

TT-P-1757B TY.I, CL.N NON-CHROMATE PRIMER: A one-component, alkyd base, corrosion-inhibiting nonchromate primer. TT-P-1757B Ty.I, Cl.N Primer is a single component, non-chromate pigmented, low-moisture sensitivity primer primarily intended for spray application on surface treated aluminum or surface treated with pre-treatment coatings MIL-C-8514C or DOD-P-15328D. This primer may be used with or without top coating. When suitable thinned, this primer may be used for dip or flowcoat application.

TT-P-1757B TY.II, CL.N NON-CHROMATE PRIMER: A low VOC one-component, alkyd base, corrosion-inhibiting nonchromate primer. TT-P-1757B Ty.II, Cl.N Primer is a single component, non-chromate pigmented, low-moisture sensitivity primer primarily intended for spray application on surface treated aluminum or surface treated with pre-treatment coatings MIL-C-8514C or DOD-P-15328D. This primer may be used with or without top coating. When suitable thinned, this primer may be used for dip or flowcoat application.

TT-P-1757A ZINC CHROMATE PRIMER (AMS3110)

PROPERTIES:

SOLIDS(Weight)………………………. 46% Minimum
PIGMENT(Weight)…………………. 53% Minimum Zinc
Chromate(Weight)…………… 85% Minimum of Pigment
COLORS…………………………….Green & Yellow

DRYING TIME:

DRY HARD………………………. Within 15 Minutes
GLOSS………………………….. Not Over 6 Units
SHELF LIFE………………………………..1 Year
THINNER…………… MIL-T-81772B TY.III or TT-X-916

ADVANTAGES:

(1). Corrosion Inhibiting
(2). Use With or Without Topcoat
(3). Fast Dry
(4). Low-Moisture Sensitivity
(5). Meets Government Specifications

 

TT-P-1757B TY.I, CL.C ZINC CHROMATE PRIMER

PROPERTIES:

SOLIDS(Weight)………………………. 59% Minimum
FINENESS OF GRIND…………………. 6 Minimum Zinc
Chromate(Weight)…………… 85% Minimum of Pigment
COLORS…………………………… Green & Yellow

DRYING TIME:

DRY HARD………………………. Within 15 Minutes
THINNER……………………… MIL-T-81772B TY.III
SHELF LIFE………………………………. 1 Year

ADVANTAGES:

(1). Corrosion Inhibiting
(2). Use With or Without Topcoat
(3). Fast Dry
(4). Low-Moisture Sensitivity
(5). Meets Government Specifications

 

TT-P-1757B TY.I, CL.N NON-CHROMATE PRIMER

PROPERTIES:

SOLIDS(Weight)………………………. 59% Minimum
FINENESS OF GRIND……………………… 6 Minimum
COLORS…………………………… Green & Yellow

DRYING TIME:

DRY HARD………………………. Within 15 Minutes
THINNER……………………… MIL-T-81772B TY.III
SHELF LIFE………………………………. 1 Year

ADVANTAGES:

(1). Corrosion Inhibiting
(2). Use With or Without Topcoat
(3). Non-Chromate Rust Inhibitor
(4). Low-Moisture Sensitivity
(5). Meets Government Specifications

 

TT-P-1757B TY.II, CL.N NON-CHROMATE PRIMER

PROPERTIES:

SOLIDS(Weight)………………………. 59% Minimum
FINENESS OF GRIND……………………… 6 Minimum
COLORS…………………………… Green & Yellow

DRYING TIME:

DRY HARD………………………. Within 15 Minutes
THINNER……………………… MIL-T-81772B TY.III
SHELF LIFE………………………………. 1 Year

ADVANTAGES:

(1). Corrosion Inhibiting
(2). Use With or Without Topcoat
(3). Non-Chromate Rust Inhibitor
(4). Low-Moisture Sensitivity
(5). Meets Government Specifications
(6). Low VOC’s

Click On The Links Below To View Documents:

Military Performance Specification TT-P-1757
TDS – TT-P-1757 TY I, CL N
TDS – TT-P-1757 TY II, CL N
TDS – TT-P-1757 TY I, CL C
TDS – TT-P-1757 TY II, CL C

TT-P-1757A ZINC CHROMATE PRIMER (AMS3110)

SURFACE PREPARATION: Steel, Non-Ferrous Metals & Galvanizing. Surface to be coated must be clean, dry, and free of all foreign contaminants including grease, oil, dirt and paint. Clean in accordance with SSPC-SP-1. Most metals should be sanded, except aluminum, which must have a base coat of pre-treatment wash primer MIL-C-8514C, followed by one wet coat of TT-P-1757A. Alloys that oxidize must be lightly sanded to remove all loose material. Dirt and dust are best removed with a stiff bristle brush and by compressed air. For exterior use and non-ferrous metals, it is recommended that TT-P-1757A be applied over pre-treatment coating conforming to MIL-C-8514C or DOD-P-15328D. Grease and oil should be removed by cleaning with appropriate solvents such as mineral spirits, lacquer wash thinner or xylene. For immersion service, ask your Griggs representative for special surface preparation recommendations.

MIXING/APPLICATION INSTRUCTIONS: Apply by spray, brush or dip to deposit a hiding coat of primer. A wet coat is necessary to secure maximum adhesion and corrosion inhibiting properties. For spraying, thin up to 15% by volume or as needed with thinner per TT-X-916 or MIL-T-81772B TY.III.

 

TT-P-1757B TY.I, CL.C ZINC CHROMATE PRIMER

SURFACE PREPARATION: Steel, Non-Ferrous Metals & Galvanizing. Surface to be coated must be clean, dry, and free of all foreign contaminants including grease, oil, dirt and paint. Clean in accordance with SSPC-SP-1. Most metals should be sanded, except aluminum, which must have a base coat of pre-treatment wash primer MIL-C-8514C, followed by one wet coat of TT-P-1757B Ty.I, Cl.C Alloys that oxidize must be lightly sanded to remove all loose material. Dirt and dust are best removed with a stiff bristle brush and by compressed air. For exterior use and non-ferrous metals, it is recommended that TT-P-1757B Ty.I, Cl.C be applied over pre-treatment coating conforming to MIL-C-8514C or DOD-P-15328D. Grease and oil should be removed by cleaning with appropriate solvents such as mineral spirits, lacquer wash thinner or xylene.

MIXING/APPLICATION INSTRUCTIONS: Apply by spray, brush or dip to deposit a hiding coat of primer. A wet coat is necessary to secure maximum adhesion and corrosion inhibiting properties. For spraying, thin up to 15% by volume or as needed with thinner per TT-X-916 or MIL-T-81772B TY.III.

 

TT-P-1757B TY.I, CL.N NON-CHROMATE PRIMER

SURFACE PREPARATION: Steel, Non-Ferrous Metals & Galvanizing. Surface to be coated must be clean, dry, and free of all foreign contaminants including grease, oil, dirt and paint. Clean in accordance with SSPC-SP-1. Most metals should be sanded, except aluminum, which must have a base coat of pre-treatment wash primer MIL-C-8514C, followed by one wet coat of TT-P-1757B Ty.I, Cl.N. Alloys that oxidize must be lightly sanded to remove all loose material. Dirt and dust are best removed with a stiff bristle brush and by compressed air. For exterior use and nonferrous metals, it is recommended that TT-P-1757B Ty.I, Cl.N be applied over pre-treatment coating conforming to MIL-C-8514C or DOD-P-15328D. Grease and oil should be removed by cleaning with appropriate solvents such as mineral spirits, lacquer wash thinner or xylene.

MIXING/APPLICATION INSTRUCTIONS: Apply by spray, brush or dip to deposit a hiding coat of primer. A wet coat is necessary to secure maximum adhesion and corrosion inhibiting properties. For spraying, thin up to 15% by volume or as needed with thinner per TT-X-916 or MIL-T-81772B TY.III.

 

TT-P-1757B TY.II, CL.N NON-CHROMATE PRIMER

SURFACE PREPARATION: Steel, Non-Ferrous Metals & Galvanizing. Surface to be coated must be clean, dry, and free of all foreign contaminants including grease, oil, dirt and paint. Clean in accordance with SSPC-SP-1. Most metals should be sanded, except aluminum, which must have a base coat of pre-treatment wash primer MIL-C-8514C, followed by one wet coat of TT-P-1757B Ty.I, Cl.N. Alloys that oxidize must be lightly sanded to remove all loose material. Dirt and dust are best removed with a stiff bristle brush and by compressed air. For exterior use and nonferrous metals, it is recommended that TT-P-1757B Ty.II, Cl.N be applied over pre-treatment coating conforming to MIL-C-8514C orDOD-P-15328D. Grease and oil should be removed by cleaning with appropriate solvents such as mineral spirits, lacquer wash thinner or xylene.

MIXING/APPLICATION INSTRUCTIONS: Apply by spray, brush or dip to deposit a hiding coat of primer. A wet coat is necessary to secure maximum adhesion and corrosion inhibiting properties. For spraying, thin up to 15% by volume or as needed with thinner per TT-X-916 or MIL-T-81772B TY.III.

AMS-3110, AMS3110